Products

  • PV-L/AT-INOX Backward curved blade centrifugal fans for dusty air

    Construction

    • Volute casing in steel sheet , protected against atmospheric agents by epoxy paint
    • Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
    • Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted
    • For high rotational speed, versions in class 3 are foreseen
    • For execution 1 – 9 – 12: mono-block support in cast iron with ball bearings, designed for easy lubrication
    • Pulleys, belts and motor support. Belt protection guard
    • Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/CE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load)

    Accessories

    • Condensation drain hole (TS)
    • Inspection door (PI)
    • Inlet counter-flange (CFA)
    • Outlet counter-flange (CFP)
    • Inlet protection guard (RA)
    • Outlet protection guard (RP)
    • Inlet flexible connector (GA)
    • Outlet flexible connector (GP)
    • Inlet vane control
    • Outlet setting shutter
    • Anti-vibration mounts

    CATALOGUE

    Quick View
  • PR-L/AT-INOX Backward curved blade centrifugal fans for clean or slightly dusty air

    Construction

    • Volute casing in steel sheet , protected against atmospheric agents by epoxy paint
    • Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
    • Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
    • For execution 1 – 9 – 12: mono-block support in cast iron with ball bearings, , designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard
    • Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/CE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load)

    Accessories

    • Condensation drain hole (TS)
    • Inspection door (PI)
    • Inlet counter-flange (CFA)
    • Outlet counter-flange (CFP)
    • Inlet protection guard (RA)
    • Outlet protection guard (RP)
    • Inlet flexible connector (GA)
    • Outlet flexible connector (GP)
    • Inlet vane control
    • Outlet setting shutter
    • Anti-vibration mounts

    CATALOGUE

    Quick View
  • ERM-EX Enhanced safety mixed flow fans

    The ERM-EX fans are the only mixed fl ow in line series in increased safety execution “EExe“ available on the market.

    The particular construction allows the installation in hazardous environment as: battery rooms, dyeing-plants, garages, etc.
    Suitable to convey clean air with working temperature from -20°C to 50°C.
    The ERM-EX are not suitable for regulation.

    Accessories

    • Reduction
    • Protection guard
    • Fixing clamps

    CATALOGUE

    Quick View
  • Dynair ZOO Belt driven axial fans

    Construction

    • Belt-driven fans
    • Airflow outside the motor
    • Housing manufactured in galvanized steel sheet
    • Impeller blades made of stainless steel AISI 304 with aluminium hub
    • Asynchronous three phase motor ball bearing motors 230/400V – 50Hz suitable for continuous running
    • Protection grade IP54, Class F

    CATALOGUE

    Quick View
  • Dynair TC-HT Centrifugal roof fans vertical discharge

    Construction

    • Base frame in galvanized steel sheet protected against atmospheric agents with epoxy finish
    • Protection guard in drawn steel rod protected against the atmospheric agents, manufactured according to UNI 10615:1997
    • Backward curved impeller in galvanized steel sheet, with high efficiency and low noise level, designed to resist at high temperature and to ensure the proper cooling of the motor in case of emergency functioning. Statically and dynamically balanced according to ISO 1940. Directly coupled to flanged motor
    • Upper cover and vertical exhaust conveyor made in galvanized steel sheet protected against atmospheric agents with epoxy finish grey RAL 7001. Superficially embossed and corrugated to rise the mechanical resistance to the strain
    • Asynchronous three-phase motor or singlephase motor manufactured according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F

    Accessories

    • Counter base to wall up (CB)
    • Inlet Protection Guard (RA)

    CATALOGUE

    Quick View
  • Dynair TAV Vertical discharge axial conveyors

    Construction

    • Outer conveyor with epoxy painted steel sheet base and with vertical panels in galvanized steel sheet
    • Double wing aluminium gravity shutters, acoustically lined
    • Coupling plate to the fan in epoxy painted steel sheet
    • Weatherproof outlet protection guard according to norm UNI 10615

    Accessories

    TAV conveyors are suitable to be installed with CC range accessories:

    • Long casing extension (CCpro)
    • Intel/Outlet cone (CCbo)
    • Flexible connections (CCga)
    • Protection guards (CCr/CCrc)
    • Flat or collar fl anges (CCf/CCfc)
    • Silencers (CCsa/CCsb)
    • External terminal box (mounted on fan casing)

    CATALOGUE

    Quick View
  • Dynair TACC Compact axial roof fans

    Construction

    • Fixing base in galvanized steel sheet
    • Casing in steel sheet, epoxy coated
    • Axial impeller with aerofoil profile blades in glass reinforce polyamide and die-cast aluminium hub, balanced according ISO 1940. Variable pitch angle in still position with setting means
    • Weatherproof upper cover in fiberglass
    • Air flow from motor to impeller
    • Protection guard on outlet side, in steel rod, manufactured according to norms UNI 10615 and weatherproof
    • Asynchronous three-phase or single-phase motor according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F
    • All suitable to S1 service (continuous working at constant load)

    Accessories

    • Inlet gravity shutter. (SA)
    • Counter-base to be walled up (CB)
    • Support base and Reduction (BA and RD)
    • Support base/Silenced reduction (PB)
    • Motor side protection grid (CCrc)

    CATALOGUE

    Quick View
  • Dynair TA-HT High performance duct axial fans F300/120 – F400

    TA-HT series are duct axial fans with aerofoil impellers and adjustable pitch angle for maximum efficiency. They are particularly indicated in those applications that request an absolute conformity to high specifications in terms of pressure and air volume.

    CATALOGUE

    Quick View
  • Dynair TA-HT High performance duct axial fans

    • TA series are duct axial fans with aerofoil impellers and adjustable pitch angle for maximum efficiency. They are particularly indicated in those applications that request an absolute conformity to high specifications in terms of pressure and air volume.

      TA-HP are particularly long lasting, robust and highly performant thanks to the aerofoil blades optimized by CFD design. Besides, the long casing construction allows an easy installation.
      They are available in a wide range of models with Ø from 400 to 1600 mm with 2, 4, 6, 8 poles motors in 6, 9 and 12 blades versions.
      The series is suitable for running in a range of temperature from -20°C to + 70°C.
      The ErP conformity is defined in phase of selection via Blowdyn 2.0 selection software or by contacting Dynair.hu.

    CATALOGUE

    ACCESSORIES

    Quick View
  • Dynair SVP Fire fighting lobbies

    The pressurization of the lobby can be made in 2 modalities according to the configuration of the lobby:

    1. Pressurization ONLY in case of emergency: this is the case of lobbies in which doors are usually kept opened.

    2. Continuous pressurization of the lobby 24h running: this is the case of lobbies in which doors are usually kept closed.

    CATALOGUE

    Quick View
  • Dynair SS-BOX Super-silent acoustic cabinet fans

    Construction

    • Main structure in galvanized steel sheet, inside lined with extra-thick acoustic insulation (50 mm)
    • Single-phase electric motor, IP44/IP20, class F, with thermal protection, suitable for speed regulation (using the suitable speed regulators shown in this catalogue)
    • Backward bladed impeller with high efficiency (mod.125-160-200-250)
    • Double inlet forward bladed fan (mod. 315-355-400-450)

    Accessories

    • Speed regulators
    • Shutters
    • Protection guards
    • Collars for fixing to the duct
    • Silencers

    CATALOGUE

    ACCESSORIES

    Quick View
  • Dynair S-CUBE KAT Backward curve centrifugal box fans – High temperature for industrial kitchens

    Construction

    • Aluminium frame with double skin sound absorbing insulated panels removable from the impeller side
    • Motor external to the stream, B5 execution directly coupled to the impeller
    • Sound absorbing and self-extinguishing material between the steel sheet layers of the panels
    • Galvanized steel sheet backward curved impeller dynamically balanced according to ISO1940
    • Punched mounting feet for an easy handling and fixing
    • Asynchronous squirrel cage three-phase or single-phase motors according to international standards IEC 60034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, Class F Suitable to S1 service (continuous running with constant load)

    Accessories

    • Water-proof protection cover
    • Anti-vibration supports
    • Floor support feet
    • Round spigot inlet cone
    • Square to round outlet adaptor
    • Flexible connector (on demand from model 35, yo be coupled with round spigot inlet cone or square to round outlet adaptor)
    • Service switch IP67
    • Grease collector tray

    CATALOGUE

    ACCESSORIES

    Quick View
  • Dynair S-Cube Backward curved centrifugal box fans

    Construction

    • Frame in extruded aluminium profiles and removable double skin panels in galvanized steel sheet; all this brings to an excellent aesthetic impact
    • Acoustic lining of the panels in self-extinguishing techno-polymer
    • Backward curved impeller directly coupled to the motor
    • B3 Motor fitted using suitable reinforced support seat
    • Support brackets with holes suitable for lifting and easy installation
    • Motor equipment:
      • Asynchronous three-phase motor or single-phase motor manufactured according to international standards IEC 60034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F
      • All suitable to S1 service (continuous working at constant load)

    Accessories

    • Weatherproof cover
    • Rainproof discharge outlet with guard
    • Anti-vibration supports
    • Floor support feet
    • Square/Round outlet connector

    CATALOGUE

    ACCESSORIES

    Quick View
  • Dynair RVT1 Threephase self-transformer speed regulator 4A

    CONSTRUCTION

    • Supply 400V-3Ph-50/60Hz.
    • Nominal current max 4 A.
    • Output voltage 1(95V)-2(145V)-3(190V)-4(240V)-5(400V).
    • Protection IP 55.
    • Pilot light
    • Housing in die-cast aluminium RAL 7001 (grey)
    • Weight Kg 11.

    CATALOGUE

    Quick View
  • Dynair RVT/2 Threephase self-transformer speed regulator 7A

    CONSTRUCTION

    • Supply 400V-3Ph-50/60Hz.
    • Nominal current max 7 A.
    • Output voltage 1(90V)-2(140V)-3(180V)-4(230V)-5(400V).
    • Protection IP 21.
    • Pilot light
    • Housing in die-cast aluminium RAL 7001 (grey) with cover in coated steel sheet RAL 7035 (light grey).
    • Weight Kg 20.

    CATALOGUE

    Quick View
  • Dynair RVT Threephase self-transformer speed regulator 2A

    CONSTRUCTION

    • Supply 400V-3Ph-50/60Hz.
    • Nominal current max 2 A.
    • Output voltage 1(90V)-2(140V)-3(180V)-4(230V)-5(400V).
    • Protection IP 54.
    • Pilot light
    • Housing in die-cast aluminium RAL 7001 (grey) with cover in plastic material RAL7035 (light)
    • Weight Kg 7.5

    CATALOGUE

    Quick View
  • Dynair RVS Single-phase self-transformer speed regulator 0,5 A

    Construction

    • Supply 230V-1Ph-50/60Hz.
    • Nominal current max 0,5 A.
    • Output voltage 1(125V)-2(140V)-3(160V)-4(200V)-5(230V).
    • Protection IP 42.
    • Housing in techno-polymer RAL9016 (white).
    • Weight Kg 0,7.

    CATALOGUE

    Quick View
  • Dynair RVM/3 Single-phase self-transformer speed regulator 7 A

    CONSTRUCTION

    • Supply 220/240V-1Ph-50/60Hz.
    • Nominal current max 7 A.
    • Output voltage 1(60V)-2(105V)-3(130V)-4(160V)-5(230V)
    • Protection IP 55.
    • Pilot light
    • Housing in die-cast aluminium RAL 7001 (grey).
    • Weight Kg 8.3

    CATALOGUE

    Quick View
  • Dynair RVM/2 Single-phase self-transformer speed regulator 4 A

    CONSTRUCTION

    • Supply 220/240V-1Ph-50/60Hz.
    • Nominal current max 4 A.
    • Output voltage 1(60V)-2(105V)-3(130V)-4(160V)-5(230V)
    • Protection IP 55.
    • Pilot light
    • Housing in die-cast aluminium RAL 7001 (grey).
    • Weight Kg 5.

    CATALOGUE

    Quick View
  • Dynair RVM Single-phase self-transformer speed regulator 1,5 A

    Construction

    • Supply 230V-1Ph-50/60Hz.
    • Nominal current max 1,5 A.
    • Output voltage 1(60V)-2(100V)-3(135V)- 4(160V)-5(185V)-6(230V).
    • Protection IP 55.
    • Pilot light
    • Housing in die-cast aluminium RAL 7001 (grey).
    • Weight Kg 2,5.

    Accessories

    • Supply 230V-1Ph-50/60Hz.
    • Nominal current max 1,5 A.
    • Output voltage 1(60V)-2(100V)-3(135V)- 4(160V)-5(185V)-6(230V).
    • Protection IP 55.
    • Pilot light
    • Housing in die-cast aluminium RAL 7001 (grey).
    • Weight Kg 2,5.

    CATALOGUE

    Quick View
  • Dynair RV/2 Single-phase electronic speed regulator 7 A

    Construction

    • Supply 230V-1Ph-50/60Hz.
    • Nominal current max 7 A (min. 4 A).
    • Timed protection fuse 8A/250V.
    • Minimum speed setting tuner.
    • Radio noise filter EMC.
    • Pilot light.
    • Housing in techno-polymer RAL 9016 (white).
    • Cooling fi n in extruded aluminium.
    • Protection IP 42.
    • Weight Kg 0,7.
    Quick View
  • Dynair REV Centrifugal roof fans with external rotor motor – Vertical discharge

    Construction

    • Base frame in galvanized steel sheet
    • Protection guard in drawn steel rod protected against the atmospheric agents, manufactured according to UNI 10615:1997
    • Backward curved wheel in galvanized steel sheet (mod. 200 in plastic), with high efficiency and low noise level
    • Outer deflector in ABS
    • External rotor motor, three-phase or single phase, IP 44/B 200-250, IP 44/F 310-400, tropycalized with integral thermal protection

    Accessories

    • Backdraught gravity shutter (TS)
    • Silencers (GR)
    • Counter base to be walled up (CB)
    • Support base for corrugated roof coverings (BA)
    • Inlet side Guard (RA)
    • Service switch
    • Speed regulator
    • Delta/start switch
    • Support base/Silenced reduction (PB). Not available for size 200

    CATALOGUE

    ACCESSORIES

    Quick View
  • Dynair REIDUCT-Q Aeraulic square ducting EI120

    With REIDUCT ducting system it is possible to design highly valuable aeraulic systems ensuring the correct fire division areas, in perfect compliance with the regulations.

    Ducts and connectors are made in metal to achieve a perfect connection between the pressurizing unit (fan) and the air intake elements. They ensure a perfect distribution of the air with low pressure losses.They complete the SVP system for fire-fighting lobbies.
    Available with circular section: REIDUCT-C

    CATALOGUE

    Quick View
  • Dynair REIDUCT-C Aeraulic circular ducting EI120

    With REIDUCT-C ducting system it is possible to design highly valuable aeraulic systems ensuring the correct fire division areas, in perfect compliance with the regulations.

    It consists of modular elements of circular  cross-section, available in diameters 200 ÷ 300mm.
    They complete the SVP system for fire-fighting lobbies.
    They are availbel with square section: REIDUCT-Q

    CATALOGUE

    Quick View
  • Dynair REC SMART+ Decentralized HRU with Touch Panel or remote controller

    Construction

    • High energy saving thanks to EC motors
    • Integrate by-pass and antifreeze functions.
    • Provided with 3 filters: the air is filtered in both flows before entering the heat exchanger.
    • Easy maintenance and cleaning: filters and heat exchanger are removable and washable.
    • Comply with EN 60335-2-80, B.T. 2014/35/UE, EMC 2014/30/UE.

    CATALOGUE

    Quick View
  • Dynair REC SMART Decentralized HRU

    Construction

    • High energy saving thanks to EC motors
    • Integrate by-pass and antifreeze functions.
    • Provided with 3 filters: the air is filtered in both flows before entering the heat exchanger.
    • Easy maintenance and cleaning: filters and heat exchanger are removable and washable.
    • Comply with EN 60335-2-80, B.T. 2014/35/UE, EMC 2014/30/UE.

    Accessories

    • Remote Speed control (min-max) and on/off switch.

    CATALOGUE

    Quick View
  • Dynair REC SanAir Decentralized HRU

    The series is available in 3 models:

     

    REC SanAir WALL
    Installation on all kind of perimetric wall.
    Unique model for horizontal or vertical installation.
    Easy installation: 2 holes of ø 100 mm are sufficient.

    REC SanAir IN WALL
    Installation on any kind of perimetrical wall.
    Built-in horizontal or vertical installation.

    REC SanAir WINDOW
    Installation on all kind of window frame with dimensions
    up to 180 mm of width and 3000 mm
    of length.

    CATALOGUE

    Quick View
  • Dynair REC PRO 90S Very high efficiency HRU with static heat exchanger

    Construction

    • Supporting structure in extruded aluminium profiles
    • Curtain panels 42 mm thick of sandwich type with special sealing gaskets; exterior finish RAL 9002 and thermal acoustic mineral wool insulation class 0 and high density
    • Filtering sections of F7 efficiency class with soft bags on the outside air circuit and M5 on exhaust air circuit, removable from the side
    • Fan sections with single inlet backward-curved blades plug-fans directly coupled to EC brushless motors
    • Very high efficiency (>90%) counterflow heat recovery, aluminium heat exchanger plates with supplementary sealing and built-in motorized by-pass device
    • Complete control panel with remote display and microprocessor for temperature control at fixed airflow, based on the operation logics designed to maximize energy savings and environmental comfort, thanks to the modulation of air flow guaranteed by the inverter technology. The unit is designer for RS485 connection to supervision systems based on Modbus RTU protocol

    Accessories

    A wide range of accessories is available : consult the catalogue.

    CATALOGUE

    Quick View
  • Dynair REC Pro 90 High efficiency HRU

    Construction

    • Casing with double skin panels in galvanized metal sheet, 42mm thick
    • External panels in prepainted galvanized steel RAL 9002
    • Internally insulated with thermo-acoustic fire-proof rockwool insulation
    • Extremely high efficiency heat recovery unit (>90%) in counter-flow aluminium plates
    • Integrated by-pass system with actuator, for free-cooling operations
    • M5 efficiency class filters on exhaust and F7 on intake, efficiency calculated according to EN 779:2012
    • Backward curved blades directly coupled with EC motors
    • Integrated control board with electronic control of all the functions: ventilation and temperature control, monitoring of the status of the filters, week programming, defrost management and anti-freeze device, fire alarm and Modbus interface.

    Accessories

    A wide range of accessories is available: consult the catalogue

    CATALOGUE

    Quick View
  • Dynair REC Pro 80R High efficiency HRU with enthalpy heat exchanger

    Construction

    • Supporting structure in extruded aluminium profiles
    • Curtain panels 42 mm thick of sandwich type with special sealing gaskets; exterior finish RAL 9002 and thermal acoustic mineral wool insulation class 0 and high density
    • Filtering sections of F7 efficiency class with soft bags on the outside air circuit and M5 on exhaust air circuit, removable from the side
    • Fan sections with single inlet backward-curved blades plug-fans directly coupled to EC brushless motors
    • High efficiency (>80%) air-to-air type heat recovery system with enthalpy rotor, EUROVENT certified, produced in aluminium alloy with hygroscopic treatment, complete with purge sector and drive belt engine designed for free-cooling management in on/off mode
    • Complete control panel with remote display and microprocessor for temperature control at fixed air flow, based on the operation logics designed to maximize energy savings and environmental comfort, thanks to the modulation of air flow guaranteed by the inverter technology. The unit is designer for RS485 connection to supervision systems based on Modbus RTU protocol

    Accessories

    A wide range of accessories is available : consult the catalogue

    CATALOGUE

    Quick View
  • Dynair REC Pro 75 High efficiency HRU

    Construction

    • The casing is made with double skin panels, with 25mm thick rockwool insulation with ­ re reaction class A2S1d0; external panels are in prepainted steel, internal panels in galvanized steel
    • Integrated by-pass system with actuator, for free-cooling operations
    • Access to fans and lters sections is ensured by doors with hinges and locking devices; additional access is given to the ­ lters thanks to lift-o panels
    • The units are complete with an electronic control device for the setting of the ventilation and temperature, monitoring of the status of the ­ lters, week programming, defrost management and anti-freeze device for the additional water coil module

    Accessories

    A wide range of accessories is available: consult the catalogue.

    CATALOGUE

    Quick View
  • Dynair REC IN LINEA TC Centralized HRU with Touch panel control – Horizontal installation

    Construction

    • Made in PPE for a perfect thermal and acoustic insulation.
    • Provided with integrated by-pass.
    • Multispeed high efficiency EC brushless motors.
    • Low sound level.
    • Filters class M6 in addition to the filters assembled.
    • Supplied with fixing plate, and RLS 1WR control panel (EC motor versions).
    • IPX2.
    • Comply with EN 60335-2-80, B.T. 2014/35/UE, EMC 2014/30/UE
    • Performance measured by BRE according to EN 13141-7, EN 13101-4, EN 5801 and EN 308.

    Accessories

    • RLS 3V – 3 speed remote controller and On/Off switch suitable for REC 280
    • Remote Touch Panel controller with coloured screen available as accessory for REC 320 (or included with REC 320 TC)

    The panel allows to manually or automatically manage (through the weekly programming) the following functions:

    • The Speed/ventilation level regulation
    • The ventilation modality (by-pass function, freecooling, only extraction, only immission)
    • The threshold humidity level over which the unit increases its speed
    • The post-ventilation function (Timer function, adjustable from 0 to 30 minutes) to delay the switching of the unit at the minimum speed)
    • The Sleep modality that allow to have the unit running silently at low speed during the night

    CATALOGUE

    Quick View
  • Dynair REC IN LINEA Centralized HRU – Horizontal installation

    Construction

    • Made in PPE for a perfect thermal and acoustic insulation.
    • Provided with integrated by-pass.
    • Multispeed high efficiency EC brushless motors.
    • Low sound level.
    • Filters class M6 in addition to the filters assembled.
    • Supplied with fixing plate, and RLS 1WR control panel (EC motor versions).
    • IPX2.
    • Comply with EN 60335-2-80, B.T. 2014/35/UE, EMC 2014/30/UE
    • Performance measured by BRE according to EN 13141-7, EN 13101-4, EN 5801 and EN 308.

    Accessories

    • RLS 3V – 3 speed remote controller and On/Off switch suitable for REC 280
    • Remote Touch Panel controller with coloured screen available as accessory for REC 320 (or included with REC 320 TC)

    The panel allows to manually or automatically manage (through the weekly programming) the following functions:

    • The Speed/ventilation level regulation
    • The ventilation modality (by-pass function, freecooling, only extraction, only immission)
    • The threshold humidity level over which the unit increases its speed
    • The post-ventilation function (Timer function, adjustable from 0 to 30 minutes) to delay the switching of the unit at the minimum speed)
    • The Sleep modality that allow to have the unit running silently at low speed during the night

    CATALOGUE

    Quick View
  • Dynair REC DUO 100 – Decentralized Heat Recovery Unit

    Construction

    • Stylish and ultra-slim front cover. Very compact dimensions.
    • Ceramic type high efficiency exchanger.
    • Provided with filters G3 class both in intake and in extract, easily removable and washable.
    • Free-cooling and Antifreeze functions.
    • EC brushless motor.
    • Comply with EN 60335-2-80, LVD 2014/35/UE, EMC 2014/30/UE.
    • IPX4
    • CE marked

    Accessories

    • RLS remote controller (on/off switch and boost actication) suitable for versions Rec Duo 100 and Rec Duo 100 MHY

    CATALOGUE

    Quick View
  • Dynair REC 320 TC Centralized HRU with control Touch Panel – Vertical Installation

    Construction

    • Casing made in galvanized steel sheet with epoxy finish
    • Internal panels in PPE for a perfect thermal and acoustic insulation.
    • Integrated filter system class G4.

    Accessories

    Wide range of accessorie : consult the catalogue.

    CATALOGUE

    Quick View
  • Dynair REC 280-320 Centralized HRU vertical Installation

    Construction

    • Casing made in galvanized steel sheet with epoxy finish
    • Internal panels in PPE for a perfect thermal and acoustic insulation
    • Integrated filter system class G4.

    Accessories

    • RLS 3V – 3 speed remote controller and On/Off switch suitable for REC 280
    • Remote Touch Panel controller with coloured screen available as accessory for REC 320 (or included with REC 320 TC)
    • The panel allows to manually or automatically manage (through the weekly programming) the following functions:
      • The Speed/ventilation level regulation
      • The ventilation modality (by-pass function, freecooling, only extraction, only immission)
      • The threshold humidity level over which the unit increases its speed
      • The post-ventilation function (Timer function, adjustable from 0 to 30 minutes) to delay the switching of the unit at the minimum speed)
      • The Sleep modality that allow to have the unit running silently at low speed during the night

    CATALOGUE

    Quick View