• Mounting plate made from galvanized steel.
• Protection guard made from sqaure micro-pressed steel sheet, protected against the elements (model 350 features a guard made out of drawn steel wire). Manufactured according to the EN ISO 12499 standard.
• High efficiency, backward curved blade impeller made from galvanized steel sheet, with low noise levels, statically and dynamically balanced statically and dynamically according to ISO 1940 standard.
• Upper cover made out of ABS plastic, with appropriate cooling slots for the motor.

Motor:        

• Asynchronous single- or three-phase motor, CE marked, with IP55 grade protection and Class F insulation,  manufactured according to the following international standards: IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE.
• Suitable for S1 Service (continuous operation at constant load).

Accessories:

• Backdraught gravity shutter (TS)
• Silencer (GR)
• Counterbase (CB)
• Mounting plate for corrugated roofs (BA)
• Inlet protection guard (RA)
• Service switch
• Acoustically insulated support base(PB)
• Flat protection guard (CCr)

Also available in a 60Hz version, and an ATEX certified version for potentially flammable or explosive environments (See: ATEX Fans).

For further details, feel free to contact KOMPEL Kft.

The post Dynair FCP-V single-speed centrifugal roof fans with vertical discharge appeared first on Dynair.hu.

• Mounting plate made from galvanized steel.
• Protection guard made from sqaure micro-pressed steel sheet, protected against the elements (model 350 features a guard made out of drawn steel wire). Manufactured according to the EN ISO 12499 standard.
• High efficiency, backward curved blade impeller made from galvanized steel sheet, with low noise levels, statically and dynamically balanced statically and dynamically according to ISO 1940 standard.
• Upper cover made out of ABS plastic, with appropriate cooling slots for the motor.

Motor:        

• Asynchronous single- or three-phase motor, CE marked, with IP55 grade protection and Class F insulation,  manufactured according to the following international standards: IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE.
• Suitable for S1 Service (continuous operation at constant load).

Accessories:

• Backdraught gravity shutter (TS)
• Silencer (GR)
• Counterbase (CB)
• Support base corrugated roofs (BA)
• Inlet protection guard (RA)
• Service switch
• Acoustically insulated support base(PB)
• Flat protection guard (CCr)

Also available in a 60Hz version, and an ATEX certified version for potentially flammable or explosive environments (See: ATEX Fans).

For further details, feel free to contact KOMPEL Kft.

The post Dynair FCP single-speed centrifugal roof fans with horizontal discharge appeared first on Dynair.hu.

• Mounting plate made from galvanized steel.
• Inlet protection guard made from micro-stretched galvanized sheet, covered in a weatherproof coating, compliant with EN ISO 12499: 2009 and UNI 80079-37-2016 standards.
• High efficiency, low noise, backward curved blade impeller made from galvanized steel sheet, statically and dynamically balanced statically and dynamically according to ISO 1940 standards.
• Upper cover made from ABS plastic, featuring cooling slots for the motor.
• Motor separated from the airflow path.
• Outer deflector made from ABS plastic (only on FCP-V version)
• Single-, or three-phase asynchronous ATEX motors in B5 standard shape, with IP55 grade protection and class F insulation, CE marked, compliant with the following standards: IEC 60034, IEC 60072, ATEX 2014/34/UE, EMC 2014/30/UE, LVD 2014/35/UE. Suitable for continuous “S1” service at constant load.

Accessories:

• Backdraught gravity shutters(TS)
• Silencer(GR)
• Counter base to be walled up (CB)
• Support base for corrugated roofs (BA)
• ATEX service switch
• Acoustically insulated support base(PB)
• Flat protection guard (CCr)

Available upon request:

• IIB+H version (presence of hydrogen)
• 60Hz versions

For further details, feel free to contact KOMPEL Kft.

The post Dynair FCP ATEX – FCP-V ATEX Single-speed centrifugal roof fans appeared first on Dynair.hu.

For maximum safety, never use any ventilator if the nature of the fumes is unknown, or the gases to be extracted could be flammable, or even explosive. In these cases, only positive ventilation can be used, blowing into the contaminated area, creating an „air wash” without sucking any gases up with the device.

Extraction and then  pressurization of explosive gases can make them even more explosive and reactive to any spark or flame.

The hydraulic, single-phase, or electric single-phase models can only extract toxic or poisonous but not explosive fumes, such as exhaust gases, welding fumes, CO2, etc.

There have been many cases where in attempt to help a victim, stunned by gas, the rescuers didn’t realise the cause of the accident, and they too were fatally poisoned.

Some toxic gases, and even the lack of oxygen are odourless, and can be fatal without any sign of danger.

Construction and specifications:

• HO727 version powered by a Honda GX120 3 hp (2,2 kW) pull start engine (ENGINE DETAILS)
• The whole device weighs 24 kg
• Airflow: up to 2100m³/h
• Outlet diameter: 20 cm
• Frame made from stainles steel, featuring a carrying handle
• Volute casing made out of polyethylene
• Dimensions: 600 x 570 x 740 mm

Available in electric (HE828) and hydraulic (PE18H) versions as well.

For further details, feel free to contact KOMPEL Kft.

The post Portable centrifugal fan powered by a Honda engine appeared first on Dynair.hu.

• Long casing made from steel sheet, painted in epoxy, equipped with fixing flanges, manufactured in compliance with the UNI ISO 6580-EUROVENT standard.
• High performance axial impeller with aerofoil blades, made completely out of die-cast aluminium. Balanced according to ISO 1940 standard. The pitch angle of the blades can be adjusted when stationary.
• Inspection door.
• Asynchronous three-phase IE2 motors,CE marked, with IP55 protection and Class H insulation, compliant with the following international standards: IEC 60034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE.
• Impeller coupled directly to the motor.
• Suitable for S1 service(continuous operation at constant load).

Accessories:

• Inlet/outlet cone (CCbo)
• Damper (CCda)
• Outlet terminal (CCot)
• High temp flexible joint (CCga-HT)
• Flat protection grid (CCr)
• Support feet (CCst)
• Counter flange (CCf)
• Counter flange with collar (CCfc)
• Cylindrical silencers with or without pod (CCsa/CCsb)
• Anti-vibration mounts

Available upon request:

• Casing protected against atmospheric agents by hot dip galvanizing
• High temperature external terminal box
• IE3 motor
• 2 speed version
• Reversible models

For further details, feel free to contact KOMPEL Kft.

The post Dynair TA-HT High performance duct axial fans F300/120 – F400 appeared first on Dynair.hu.

If you have any further questions, feel free to contact KOMPEL Kft!

The post Dynair Inverter and Line filter appeared first on Dynair.hu.

If you have any further questions, feel free to contact KOMPEL Kft!

The post Dynair RVT/2 Threephase self-transformer speed regulator 7A appeared first on Dynair.hu.

If you have any further questions, feel free to contact KOMPEL Kft!

The post Dynair RVT1 Threephase self-transformer speed regulator 4A appeared first on Dynair.hu.

If you have any further questions, feel free to contact KOMPEL Kft!

The post Dynair RVT Three-phase self-transformer speed regulator 2A appeared first on Dynair.hu.

If you have any further questions, feel free to contact KOMPEL Kft!

The post Dynair RVM/3 Single-phase self-transformer speed regulator 7 A appeared first on Dynair.hu.